Please ensure Javascript is enabled for purposes of website accessibility

arrow spine question?

Discussion in 'Tech Talk' started by 10ptdreamer, Jun 12, 2011.

  1. 10ptdreamer

    10ptdreamer Weekend Warrior

    Joined:
    Sep 11, 2010
    Posts:
    72
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Gadsden, Alabama
    I am currently shooting a gold tip xt hunter 5575 with a .400 spine. I am wanting to go to a gold tip velocity hunter with a .413 spine. My bow is a 28.5 draw length set on 70 lb draw. I am wanting to pick up a touch more speed and when season gets here I will go down to about 60 lb draw. Is this spine safe for me to swap over to? The first arrow is 8.4 grains per inch and the second will be 7.4 gpi
     
    Last edited: Jun 12, 2011
  2. Boodaddy

    Boodaddy Weekend Warrior

    Joined:
    May 9, 2011
    Posts:
    131
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Northern Mississippi
    You will be fine with that but don't go any higher on spine, atleast until you shoot 60 pounds but even then I wouldn't.
     
  3. 10ptdreamer

    10ptdreamer Weekend Warrior

    Joined:
    Sep 11, 2010
    Posts:
    72
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Gadsden, Alabama
    so the higher the spine number the weaker the spine? I am not very educated on spine ratings.
     
  4. Boodaddy

    Boodaddy Weekend Warrior

    Joined:
    May 9, 2011
    Posts:
    131
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Northern Mississippi
    Yeah that's right but becareful looking at numbers. Sometimes company like Carbon Express tend to put 250 on the shaft but its not a 250 spine. It's actually a higher spine. Whenever buying new arrows definately go by the chart.
     
  5. headstrong

    headstrong Die Hard Bowhunter

    Joined:
    Jul 11, 2010
    Posts:
    1,164
    Likes Received:
    74
    Dislikes Received:
    0
    Location:
    southeast wisconsin
    It's going to depend on the arrow length. If your arrows are 29" It would be safer to run a 350 Then you could use them at 60-70#. Don't think I would use a .400 or .413 if you decide to go back to 70#
     
  6. KodiakArcher

    KodiakArcher Die Hard Bowhunter

    Joined:
    Feb 15, 2009
    Posts:
    2,229
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Anchorage, AK
    It's better to go slightly stiff for shooting broadheads and you definitely don't want it on the weak side. If you're going off a chart and are on the edge between two spine weights, pick the stiffer spine (lower deflection rating). You may have to shift to a totally different shaft to get one in the right spine and at the weight (gpi) you want.

    A lot of this conjecture depends on your bow though. For instance; I found that the 2009-2010 Elites like a spine a little on the weak side.
     
    Last edited: Jun 13, 2011
  7. 10ptdreamer

    10ptdreamer Weekend Warrior

    Joined:
    Sep 11, 2010
    Posts:
    72
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Gadsden, Alabama
    I bought a carbon express 250 blue streak today. It weighs out at 341 where my gold tips weighed out at 369. Dont know yet how that translates into fps but will chrony them soon. they seem to almost hit in the same spots from 20 to 40 yards. Would a drop away rest help me pick up any speeds?
     
  8. Boodaddy

    Boodaddy Weekend Warrior

    Joined:
    May 9, 2011
    Posts:
    131
    Likes Received:
    0
    Dislikes Received:
    0
    Location:
    Northern Mississippi
    Several factors come into play on speed and what spine you should use. A drop away COULD help your speed but then again, shooting blazers COULD too! That doesn't guarantee anything. Everyone screams speed but force kills. Refer back to the pebble and the rock. Why not lose 5 fps to gain a total pass through? Can you tell a difference in 5 fps? No. Can the Swamp Donkey at 20 yards opening day? No. Load some weight up brother and put it through a 350 engine block!
     

Share This Page