This is the process I use to make the broadheads that I hunt with when Im hunting with trad gear.
I use 125 grain field points and reshape them to remove the shoulders. this step may not be necessary buy It looks nice.
the blades are cut from a .039 thick bandsaw blade.
the jig for slotting the field point is made of steel and clamps the point while the spacer (piece of hacksaw blade) Leaves room for the saw to pass between the two halves to cut the slot.
I then polish the two pieces and make sure I have a good fit up.
Next I braze the two parts together although I think solder or even J.B. Weld would suffice. I may try this on the next batch because brazing is messy and I have to quench afterward to make sure the heads are hard.
After cleaning and polishing again, I use a cold bluing to protect the heads and then a light coat of oil.
Finished weight, 165 grains. about 1 inch wide (15/16) and 1 1/4 long.
After reading Dr. Ashby's report on single bevel broadheads.(right after I finished the last batch of double bevel heads) I just had to make some single bevel heads. It just makes so much sense. I will test both to see if I get his results.
After making the first set of single bevel heads, I made a new set with a longer profile. This is closer to what Im looking for.
After finishing my homemade broadheads and I was itching to try them out . I am really curious about the single bevel blades and what they will do.
As luck would have it, a neighbor brought me a fresh archery kill to process for him. I asked him if it would be ok to test my heads on his deer. He didn't mind since he wanted the whole deer ground into sausage and/or burger. So here she is. All 68 pounds of her (dressed) I would have loved to be trying this on a 150 pound deer but beggars can't be choosers.
I made three shots from 10 yards with my 45 pound longbow that shoots an arrow at a blazing 142 FPS. the first two were through the ribs and the final one hit the shoulder blade at the point where the flat and the "T" meet, right near the ball joint. This is (in my opinion) the largest and thickest bone section in the upper shoulder. I admit that hitting this far forward is not a good place to aim on a live animal but things happen beyond our control. I of course hit this spot with pin point precision on purpose.
The rib shots were complete pass throughs but the shoulder shot ended up with just the fletches sticking out entrance side. I know there were no lungs in the deer but they don't offer much in the way of resistance any way. Also consider that this deer was cold and stiff as rigor mortise had set in so I consider all things equal.
Right off the bat, I noticed the "S" shaped cuts that Dr. Ashby had spoke about. This was the case on both the entrance and exit holes.
*** Word of caution***
When you pull the arrow back out of the deer (through a bone) and you have sharpened your broadheads on the trailing edge as well as the main edge. Make sure to keep your fingers clear even though you need to hold the deer steady while retrieving the arrow.
After a brief bit of first aid, I began to skin the deer, I noticed that both of the rib shots had completely missed hitting ribs on both sides. My goal was to break a rib to see the results but I must have used up all my luck..... I mean skill on that shoulder shot.
I then removed the shoulder and boned it out.
Just as described by Dr. Ashby, the "S" shaped cut and the bone had split completely being held at the joint end by only some soft fibers.
As expected, the single bevel head is a real bone breaker/splitter. I know this is a very small deer but again, I was using a rather low power bow. Take from this what you will but I am even more pleased with the single bevel heads. This sort of thing is not necessary with todays super fast and powerful bows hunting whitetails but for those using traditional archery gear, or those going after large or dangerous game, we are looking for every advantage we can get
Below are the first two of the new half dozen heads I will be hunting with this year. They are similar to the heads I have made in prior years only these are a bit longer to give a better aspect ratio ( 2.6 : 1 ) and have the added weight I was looking for to be used with my longbow . They are just under 1 inch wide with a blade thickness of .039. The blades are single bevel. They are made the same way as prior heads where the blades are pinned to the ferrule.
The real test is how they perform onlive game. In 2008, I was able to try them out while using a homemade bow I had built for my Son. It seems they work well.
thats pretty cool to make your own broadheads, they look wicked; goodluck continuing to use them.
Hoyt Vipertech bow
Quality Archery Design arrow rest
Trophy Ridge hit-man 7 pin sight
Carbon Express maxima hunter 250 arrows
Slick Trick magnum 100 4 blades
Nextbuk Outdoors Pro Staff
Buck Fever Synthetics Pro Staff - "Make Bucks Hunt You"!
Very cool post, those heads look sweet.
--Shut up and hunt--
--Quit your grinnin and get to skinnin--
That is just way too cool!
1John 1:9 If we confess our sins, he is faithful and just to forgive us our sins, and to cleanse us from all unrighteousness.
BRING BACK BRUCE!!!
Charter Member of "Team Kill"
I'd like to apologize up front for posting those pictures of my face (I did however warn you about the graphic nature of this post) I have been told I have a face more suited for work in Radio. I'll try not to do it again.
Awsome. Do you make the jigs for sale
Those are some nasty-looking home-made heads. Great job!
So... are you a machinist or a mill wright?
- Jerry -
SGT USAF '64-'68
Mathews Chill with Rock Mods! /50# 27" Draw
Easton HEXX w/Blazer Vanes /Nocturnals
125gr SlickTrick RazorTrick Broadheads
Trophy Ridge REACT 5-pin Sight
Axion GLM 8oz Matrix Stabilizer
QAD LD Drop Away Rest
Mathews Halon 6/Mathews Z7 Magnum/29"/70lbs.
HHA KingPin Optimizer Lite and DS-5519 Sights
Mathews and QAD Ultra Rest HDX Right Hand, Black and Red
Easton Injexion Deep Six Full Metal Jacket
Nockturnal X-Nocks (Red)
Mathews Web HD and Web CT Quivers
Ktech 7.5 and Axion 5 in. Stabilizers, Black and Lost Camo
Rage Hypodermic Broadheads
Nikon Archer's Choice Rangefinder
"Most People are the Cause of Their Own Suffering!"
2013, 2014, 2015 GTG Attendee
2013 GTG Long Haul Award
You do know that he is banned and this thread is from 2010.
Really is a nice job on a single bevel. Pretty unreal how such a old design is still so practical...love the picture of it through the bone...no head design can compare to the performance of a single bevel when it it comes to passing though bone.
"A man with no enemies is a man with no character.”...........Paul Newman
"It is good to have and end to journey toward; but it is the journey that matters, in the end.".. Ernst Hemingway
"Happiness is a blood trail".......Me, Trial153
The Break Team Hunter
I vote to let Mr. Crabtree back on the forum !!!!!!!!!
Let's start a petition, who's with me !!???!!???
Crabtree !!!! Crabtree !!!!
2013 PSE OMEN MAX (Damien)
70lb 29" draw
TruGlo carbon xs 4 pin
125gr Slick Trick Viper trick
Carbon Express Red 350's 450grain arrows at 311fps......96ish ke of passin thru
Moderator Blue collar bowhunting FB group